|
| | Phosphine Basic information |
| | Phosphine Chemical Properties |
| Melting point | -133° | | Boiling point | −87.5 °C(lit.) | | density | 0.491 (estimate) | | vapor density | 1.15 (vs air) | | vapor pressure | 3905kPa at 25℃ | | form | colorless gas | | Water Solubility | 0.26 volumes in H2O (20°C); insoluble hot H2O; slightly soluble alcohol, ether, cuprous chloride solutions [HAW93] [MER06] | | Merck | 13,7424 | | Exposure limits | TLV-TWA 0.42 mg/m3 (0.3 ppm) (ACGIH and OSHA); STEL 1.4 mg/m3 (1 ppm) (ACGIH); IDLH 200 ppm (NIOSH). | | Stability: | Stable, but pyrophoric - spontaneously flammable in air. Note the very wide explosion limits. Incompatible with oxidizing agents, halogens, nitric acid. | | CAS DataBase Reference | 7803-51-2(CAS DataBase Reference) | | NIST Chemistry Reference | Phosphine(7803-51-2) | | EPA Substance Registry System | Phosphine (7803-51-2) |
| | Phosphine Usage And Synthesis |
| Description | Phosphine is a colorless, flammable gas that
is heavier than air and has a characteristic odor
described as being similar to decaying fish. Pure
phosphine is claimed to be odorless, even at a
level of 200 ppm. The odor threshold for commercially available phosphine ranges from 0.02
ppm to 3 ppm. It has an autoignition temperature of 100°F (37.8°C) and ignites spontaneously when traces of other phosphorous hydrides such as diphosphine are present. For all
practical purposes, phosphine should be handled
both as a pyrophoric and highly toxic gas.
Phosphine is stable at room temperature and
begins to decompose at about 707°F (375°C),
with complete decomposition at about 1100°F
(593°C). Phosphine is readily oxidized by
common oxidizers such as potassium permanganate and sodium hypochlorite. Unlike arsine,
it will have some reaction with the alkalis.
Phosphine is a strong reducing agent and can
precipitate a number of heavy metals from solutions of their salts. It will react violently with
oxidizers such as oxygen, chlorine, fluorine, and
nitric oxide.
Phosphine is shipped in the pure form as a
liquefied gas, and is also commonly available as
a mixture when blended with hydrogen or inert
gases. | | Chemical Properties | Phosphine is a pyrophoric chemical and spontaneously flammable in air. It is incompatible with strong oxidising agents, halogens, nitric acid. It has the odour of garlic or decaying fish. It is slightly soluble in water. It is flammable and is an explosive gas at ambient temperature. Phosphine decomposes on heating or on burning producing toxic fumes including phosphorus oxides. It reacts violently with air, oxygen, oxidants such as chlorine and nitrogen oxides, metal nitrates, halogens, and other toxic substances, and causes fire and explosion hazard.
| | Chemical Properties | Phosphine is a colorless gas that is shipped as liquefied compressed gas. Odorless when pure. It has the odor of garlic or the foul odor of decaying fish. The level at which humans detect the odor of phosphine (odor threshold) does not provide sufficient warning of dangerous concentrations. Phosphine presents an additional hazard in that it ignites at very low temperatures. Shipped as a liquefied compressed gas. The pure compound is odorless. The Odor Threshold is 0.14 ppm. | | Physical properties | Colorless gas with an odor of decaying fish; flammable; burns with a luminous flame; density 1.492 g/L; liquefies at -87.7°C; solidifies at -133°C; critical temperature 51.35°C; critical pressure 64.55 atm; slightly soluble in water; the solution is weakly basic. | | Occurrence | Phosphine is produced naturally in small amounts in marshy lands, especially in damp graveyards, resulting from bacterial decay of animal and vegetable matter containing phosphorus. The atmospheric oxidation of impure phosphine (containing trace amounts of diphosphine, P2H4) emits pale flickering lights, the so-called “Will o’ the wisps” or “corpse candles” seen on dark nights. The compound has very little commercial application. It is used to prepare phosphonium salts, which also can be made by other processes. | | Uses | Phosphine is used in a variety of organic preparations and in the preparation of phosphonium
halides. It is commonly used (in gas mixtures)
as a doping agent for n-type semiconductors,
and as a pure gas in the manufacture of
light-emitting diodes. It is also used as a fumigant at low concentrations for grain. | | Uses | Phosphine is used as a fumigant, in the synthesis of many organophosphorus compounds, and as a doping agent for electronic components. It occurs in the waste gases from plants manufacturing semiconductors and thin-film photovoltaic cells. The presence of bound residues of phosphine in fumigated commodities has been reported (Rangaswamy and Sasikala 1986). | | Uses | Phosphine is the most widely used fumigant for insect con-trol in the durable commodities throughout the world. It is increasingly used as a treatment to re-place methyl bromide especially because of its low cost, fast dispersion in the air and low residues. Versatility of use is a major advantage for phosphine, as it can be used in a variety of storage buildings, during transit (e.g. in ship holds) or in plastic sheet enclosures. It is close to an ideal fumigant except for few drawbacks: slow activity, the rapid increase in insect resistance, flammability at higher concentrations (>900 ppm) and corrosion of copper, silver and gold. The phosphine resistance among the insect populations was found to be the result of selection pressure caused by inadequate fumigations in the storage units; storage facilities not adequately sealed before fumigation; and fumigant concentrations not being monitored. The understanding of phosphine resistance mechanism, improved monitoring tactics and management of resistance are the priorities in tackling the problem (Rajendran, 2001). The other problems like corrosion and flammability were found to be limited by using the combination of heat (30–36℃), carbon dioxide (3–7%) and phosphine at 80–100 ppm, while achieving a complete insect control.
| | Definition | A colorless gas that is
slightly soluble in water. It has a characteristic
fishy smell. It can be made by reacting
water and calcium phosphide or by the action
of yellow phosphorus on a concentrated
alkali. Phosphine usually ignites
spontaneously in air because of contamination
with diphosphine. It decomposes into
its elements if heated to 450°C in the absence
of oxygen and it burns in oxygen or
air to yield phosphorus oxides. It reacts
with solutions of metal salts to precipitate
phosphides. Like its nitrogen analog ammonia
it forms salts, called phosphonium
salts. It also forms complex addition compounds
with metal ions. As in ammonia,
one or more of the hydrogen atoms can be
replaced by alkyl groups. | | Definition | phosphine: A colourless highlytoxic gas, PH3; m.p.-133°C; b.p.–87.7°C; slightly soluble in water.Phosphine may be prepared by reactingwater or dilute acids with calciumphosphide or by reactionbetween yellow phosphorus and concentratedalkali. Solutions of phosphineare neutral but phosphinedoes react with some acids to givephosphonium salts containing PH4+ions, analogous to the ammoniumions. Phosphine prepared in the laboratoryis usually contaminated withdiphosphine and is spontaneouslyflammable but the pure compound isnot so. Phosphine can function as aligand in binding to transition-metalions. Dilute gas mixtures of very purephosphine and the rare gases areused for doping semiconductors. | | Definition | ChEBI: The simplest phosphine, consisting of a single phosphorus atom with three hydrogens attached. | | Production Methods | Phosphine, also known as phosphorated hydrogen or hydrogen
phosphide (PH3), has no direct commercial use. However,
it may be generated from aluminum or zinc phosphide
and water for grain fumigation. It may be present in phosphorus
as a polymer or generated at low rates under alkaline
conditions and at a temperature of 85C. The generation of
acetylene from calcium carbide containing calcium phosphide
as an impurity and metal processing procedures in
which phosphides are formed are the most frequent sources
of industrial hygiene problems with phosphine. | | Preparation | Phosphine, unlike ammonia, is not made by direct union of elements. However, phosphine is prepared from other phosphorus compounds by several methods.
Phosphine can be prepared by alkaline hydrolysis of white phosphorus. Thus, a strong aqueous solution of caustic potash when boiled with white phosphorus yields hypophosphite with liberation of phosphine:
P4 + 3KOH + 3H2O → 3KH2PO2 + PH3↑
Caustic soda or barium hydroxide can be used instead of caustic potash. The apparatus should be free from air. Either hydrogen or natural gas may be passed through the generator to purge out all residual oxygen out from the flask to prevent any explosion. A small amount of diphosphine, P2H4 also is produced in the reaction. The latter inflames spontaneously in air. Diphosphine, which is an unstable liquid at 20°C, may be removed by condensation in a tube immersed in a freezing mixture; or by passing through concentrated hydrochloric acid; or slowly by photochemical decomposition by exposing to light.
Phosphine also is prepared by reduction of a solution of phosphorus trichloride with lithium aluminum hydride in dry ether under warm conditions. The solution of the latter is added from a dropping funnel to phosphorus trichloride solution in dry ether placed in a water bath.
4 PCl3 + 3LiAlH4 → 3 LiCl + 3AlCl3 + 4PH3↑
The flask is connected to a reflux condenser to condense down solvent ether back into the flask. Phosphine is collected over water as a moist gas. Dry phosphine may alternatively be condensed in a U-tube placed in freezing mixture.
Phosphine may be produced by mixing a solution of phosphonium iodide with potassium hydroxide:
PH4I + KOH → KI + H2O + PH3↑
Another preparation method involves treating metallic phosphide with dilute acids:
Ca3P2 + 6HCl → 3CaCl2 + 2PH3↑
This method was applied earlier to produce floating signal flares at sea. Floating cans of calcium phosphide were punctuated to admit sea water to generate phosphine, which ignited spontaneously to emit flares. The flares could not be extinguished by wind or water. | | Air & Water Reactions | Highly flammable. Usually ignites spontaneously in air. Burns with a luminous flame [Merck 11th ed. 1989]. Insoluble in water. | | Reactivity Profile | Phosphine is a reducing agent. Ignites spontaneously in air when pure [Sidgwick, 1950, p. 729]. Liquefied Phosphine can be detonated [Rust, 1948, p. 301]. Ignites or reacts violently with boron trichloride, dichlorine oxide, halogens (bromine, chlorine, iodine), metal nitrates, nitrogen oxides, nitric acid, nitrous acid, nitrogen trichloride [Bretherick, 5th ed., 1995, p. 1562]. Forms explosive mixtures with even small amounts of oxygen. Autoignites at low pressures [Fisher, E. O. et al., Angew. Chem., 1968, 7, p. 136]. | | Hazard | Phosphine is a highly toxic and flammable gas. Acute effects are irritation, tightness of chest, painful breathing, and lung damage. High concentration can be fatal. A fire hazard. | | Health Hazard | Phosphine is a super- toxic gas with a probable oral lethal dose of 5 mg/kg or 7 drops for a 150 pound person. An air concentration of 3 ppm is safe for long term exposure, 500 ppm is lethal in 30 minutes, and a concentration of 1,000 ppm is lethal after a few breaths. | | Health Hazard | Phosphine is a highly poisonous gas. The symptoms of its acute toxic effectsin humans can be respiratory passage irritation, cough, tightness of chest, painful breathing, a feeling of coldness, and stupor. Inhalation of high concentrations of phosphine in air can cause lung damage, convulsion, coma, and death. In addition to damaging the respiratory system, exposure to this compound can cause nausea, vomiting, diarrhea, and depression of the central nervous system. Exposure to a concentration of 1000 ppm in air for 5 minutes can be fatal to humans (NIOSH 1986).
LC50 value, inhalation (rats): 11 ppm (15.3 mg/m3)/4 h
Chronic exposure is likely to cause phosphorus poisoning. Nutritional and toxicological studies indicated that ingestion of a phosphine-fumigated diet by rats for 2 years did not cause marked modification of growth, feed intake, functional behavior, or the incidence or type of tumors (Cabrol Telle et al. 1985). | | Fire Hazard | Phosphine can explode with powerful oxidizers. The gas is heavier than air and may travel along the ground to an ignition source. Container may explode in heat of fire. When heated to decomposition, Phosphine emits highly toxic fumes of phosphorus oxides. Reacts violently with: air; boron trichloride; bromine; chlorine; chlorine monoxide; nitric acid; nitric oxide; nitrous oxide; nitrogen trioxide; silver nitrate; nitrous acid; mercuric nitrate; nitrogen trichloride; oxygen; and (potassium plus ammonia). Stable up to 131F. May become unstable at high temperatures. | | Flammability and Explosibility | Highlyflammable | | Agricultural Uses | Fumigant, Insecticide: Phosphine gas is used indoors to control a broad spectrum of insects for non-food/non-feed commodities in sealed containers or structures. There are no homeowner or agricultural row crop uses for this product. The end-use product is a poisonous liquefied gas under pressure, and is A U.S. EPA restricted Use Pesticide (RUP) due to the acute inhalation toxicity of phosphine gas. Phosphine is only occasionally used in industry, and exposure usually results accidentally as a byproduct of various processes. Exposures may occur when acid or water comes in contact with metallic phosphides (aluminum phosphide, calcium phosphide). These two phosphides are used as insecticides or rodenticides for grain, and phosphine is generated during grain fumigation. Phosphine may also evolve during the generation of acetylene from impure calcium carbide, as well as during metal shaving, sulfuric acid tank cleaning, rustproofing, and ferrosilicon, phosphoric acid and yellow phosphorus explosive handling. U.S. EPA restricted Use Pesticide (RUP). Currently listed as “pending” in the EU. | | Trade name | ECO2 FUME TM®; VAPORPH3OS® | | Materials Uses | Phosphine is noncorrosive and, therefore, may
be used with most ofthe commercially available
metals. However, since phosphine is mainly
used for the electronics industry, type 316 and
316L stainless steel is recommended for the gas
delivery systems. Stainless steel regulators
should be used for all high purity applications
with phosphine and phosphine mixtures. In all cases, systems should be adequately designed to
withstand the pressures to be encountered. | | Safety Profile | A poison by inhalation. A very toxic gas whose effects are not completely understood. The chef effects are central nervous system depression and lung irritation. There may be pulmonary edema, dilation of the heart, and hyperemia of the visceral organs. Inhalation can cause coma and convulsions leading to death within 48 hours. However, most cases recover without after-effects. Chronic poisoning, characterized by anemia, bronchitis, gastrointestinal disturbances, and visual, speech, and motor disturbances, may result from continued exposure to very low concentrations.Very dangerous fire hazard by spontaneous chemical reaction. Moderately explosive when exposed to flame. Explosive reaction with dichlorine oxide, silver nitrate, concentrated nitric acid, nitrogen trichloride, oxygen. Reacts with mercury(Ⅱ) nitrate to form an explosive product. Ignition or violent reaction with air, boron trichloride, Br2, Cl2, aqueous halogen solutions, iodine, metal nitrates, NOx NCh, NO3, N20, HN02, K + NH3, oxidants. The organic derivatives of phosphine (phosphines) react vigorously with halogens. To fight fire, use CO2, dry chemical, or water spray. Dangerous; when heated to decomposition it emits highly toxic fumes of POx. Used as a fumigant, doping agent for electronic components, and in chemical synthesis | | Potential Exposure | Phosphine is used as a fumigant; in the semiconductor industry, as a doping agent for electronic components to introduce phosphorus into silicon crystals; in chemical synthesis; used as a polymerization initiator; as an intermediate for some flame retardants. Also, exposures may occur when acid or water comes in contact with metallic phosphides (aluminum phosphide, calcium phosphide). These two phosphides are used as insecticides or rodenticides for grain, and phosphine is generated during grain fumigation. When phosphine toxicity is suspected, but phosphine exposure is not obvious, one should suspect transdermal contamination and/or ingestion of phosphides. Phosphine may also evolve during the generation of acetylene from impure calcium carbide, as well as during metal shaving; sulfuric acid tank cleaning; rustproofing, ferrosilicon, phosphoric acid; and yellow phosphorus explosive handling. | | Physiological effects | Phosphine is a highly toxic gas that can cause
death from delayed pulmonary edema or from tissue anoxia secondary to interference with
tissue respiration. Phosphine is both an irritant
and a general systemic poison. Its action is
similar to that of hydrogen sulfide.
Symptoms of irritation include lacrimation,
substernal chest pain and chest tightness, shortness of breath, a slight cough, and cyanosis.
Nonlethal exposures can result in symptoms
referable to the gastrointestinal tract and the
nervous system. Abdominal symptoms include
nausea, vomiting, severe epigastric pain, and
diarrhea. Neurologic symptoms include vertigo,headache, restlessness, intentional tremor, lack
of muscular coordination, double vision,
drowsiness, and a decreased sensation in the
extremities. Death in humans has occurred after
exposures as low as 8 ppm for 1-2 hours.
Additional acute toxic symptoms involve cardiac abnormalities, liver dysfunction, and kidney inflammation. Agitated psychotic behavior
can occur.
ACGIH recommends a Threshold Limit
Value-Time-Weighted Average (TLV-TWA)
of 0.3 ppm (0.42 mg/m3) for phosphine. The
TLV-TWA is the time-weighted average concentration for a normal 8-hour workday and a
40-hour workweek, to which nearly all workers
may be repeatedly exposed, day after day, without adverse effect. ACGIH also recommends a
Threshold Limit Value-Short Term Exposure
Limit (TLV-STEL) of 1 ppm (1.4 mg/m3) for
phosphine. The TLV-STEL is the IS-minute
TWA exposure that should not be exceeded at
any time during a workday even if the 8-hour
TWA is within the TLV-TWA. Exposures
above the TLV- TWA up to the STEL should
not be longer than 15 minutes and should not
occur more than 4 times per day. There should
be at least 60 minutes between successive exposures in this range.
OSHA lists an 8-hour Time-Weighted Average-Permissible Exposure Limit (TWA-PEL)
of 0.3 ppm (0.4 mg/m3) for phosphine. TWAPEL is the exposure limit that shall not be exceeded by the 8-hour TWA in any 8-hour work
shift of a 40-hour workweek. | | Environmental Fate | Because of its very high vapor pressure, phosphine exists in air
as a gas and volatilizes from water and surface soil. At high
concentrations, the vapors may spontaneously combust in air.
Atmospheric phosphine may be degraded by photochemically
produced hydroxyl radicals with an expected half-life of less
than 1 day. Phosphine can bind to subsurface soils and is
degraded quickly. The chemical does not accumulate in the
food chain. | | storage | Since phosphine is an extremely toxic and
flammable gas, appropriate precautions must be
taken in its storage and handling. Store and use
phosphine and phosphine mixtures only in ventilated gas cabinets, exhaust hoods, or highly
ventilated rooms that supply a large volume of
forced air ventilation. Explosion-proof forced
draft gas cabinets or fume hoods are recommended. Use piping and equipment adequately
designed to withstand the pressures to be encountered.
Since phosphine may form explosive mixtures
with air, keep it away from heat and all ignition
sources such as flames and sparks. All lines,
connections, equipment, etc. must be thoroughly
checked for leaks and grounded prior to use.
Only use spark-proof tools and explosion-proof
equipment. The compatibility with plastics and
elastomers should be confirmed.
For basic safety information on the handling
of compressed gas cylinders, refer to CGA P-I,
Safe Handling of Compressed Gases in Containers. | | Shipping | UN2199 Phosphine, Hazard Class: 2.3; Labels: 2.3-Poisonous gas, 2.1-Flammable gas, Inhalation Hazard Zone A. Cylinders must be transported in a secure upright position, in a well -ventilated truck. Protect cylinder and labels from physical damage. The owner of the compressed gas cylinder is the only entity allowed by federal law (49CFR) to transport and refill them. It is a violation of transportation regulations to refill compressed gas cylinders without the express written permission of the owner. | | Purification Methods | PH3 is best purified in a gas line (in a vacuum) in an efficient fume cupboard. It is spontaneously flammable, has a strong odour of decayed fish and is POISONOUS. The gas is distilled through solid KOH towers (two), through a Dry ice-acetone trap (-78o, to remove H2O, and P2H4 which spontaneously ignites with O2), then through two liquid N2 traps (-196o), followed by distillation into a -126o trap (Dry ice-methylcyclohexane slush), allowed to warm in the gas line and then sealed in ampoules preferably under N2. IR: max 2327 (m), 1121 (m) and 900 (m) cm-1 . [Klement in Handbook of Preparative Inorganic Chemistry (Ed. Brauer) Academic Press Vol I pp 525-530 1963, Gokhale & Jolly Inorg Synth IX 56 1967.] PH3 has also been absorbed into a solution of cuprous chloride in hydrochloric acid (when CuCl.PH3 is formed). PH3 gas is released when the solution is heated, and the gas is purified by passage through KOH pellets and then over P2O5. Its solubility is 0.26mL/1 mL of H2O at 20o, and a crystalline hydrate is formed on releasing the pressure on an aqueous solution. | | Toxicity evaluation | Phosphine toxicity occurs in insects, rodents, and humans via
a common mechanism of respiratory inhibition. The chemical
is a noncompetitive inhibitor of cytochrome oxidase in mitochondria.
Human case reports and animal studies have shown
that phosphine also inhibits the activity of catalase and
cholinesterase, decreases glutathione content, and reacts with
hemoglobin. Overall, the studies show oxidative stress as the
mechanism of phosphine toxicity. | | Incompatibilities | Phosphine reacts with acids, air, copper, moisture, oxidizers, oxygen, chlorine, nitrogen oxides; metal nitrates; halogens, halogenated hydrocarbons; copper and many other substances, causing fire and explosion hazard. Extremely explosive; may ignite spontaneously on contact with air at (or about) 100C. Attacks many metals. Incompatible with oxidizers (chlorates, nitrates, peroxides, permanganates, perchlorates, chlorine, bromine,fluorine, etc.); contact may cause fires or explosions. Keep away from alkaline materials, strong acids, amines, ammonia, ethylene oxide, metal nitrates, nitrous acid, phosgene, strong bases. | | Waste Disposal | Return refillable compressed gas cylinders to supplier. Consult with environmental regulatory agencies for guidance on acceptable disposal practices. Generators of waste containing this contaminant (≥100 kg/mo) must conform with EPA regulations governing storage, transportation, treatment, and waste disposal. In accordance with 40CFR165, follow recommendations for the disposal of pesticides and pesticide containers. Must be disposed properly by following package label directions or by contacting your local or federal environmental control agency, or by contacting your regional EPA office. Controlled discharges of Phosphine may be passed through 10% NAOH solution in a scrubbing tower. The product may be discharged to a sewer. | | GRADES AVAILABLE | Phosphine is supplied in a number of grades,
primarily as electronic grade, with a purity of
99.999 percent on a hydrogen-free basis.An MOCVD grade is also offered with a purity of 99.9998 percent. |
| | Phosphine Preparation Products And Raw materials |
|
